Колонки JL Audio C1-650

Колонки JL Audio C1-650

8790р.
Производители
Код товара: 70976
Наличие Есть в наличии

Краткое описание

Тип: компонентные Типоразмер: 16,5 см (6 1/2") Количество полос: две Импеданс: 4Ом Защитные решётки:...

Дополнительно:

  • Гарантия 12 месяцев
  • Защитные решётки нет
  • Импеданс 4Ом
  • Количество полос две
  • Краткое описание 16,5 СМ ДВУХКОМПОНЕНТНАЯ АКУСТИЧЕСКАЯ СИСТЕМА. 225/50 Вт, 59-22 000 Гц, 91 дБ/Вт/м ЦЕНА - ЗА КОМПЛЕКТ!
  • Номинальная мощность до 50Вт
  • Тип компонентные
  • Типоразмер 16,5 см (6 1/2")
Тип:
компонентные



Типоразмер:
16,5 см (6 1/2")



Количество полос:
две



Импеданс:
4Ом



Защитные решётки:
нет



Номинальная мощность:
до 50Вт



Гарантия:
12 месяцев



Бренд:
JL




C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles.



To facilitate fit, multi-application adaptor rings are included for the C1-650 woofers, allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the woofers will also fit into many "6-inch" speaker locations as well. Surface and flush mounts are included with C1 tweeters for maximum installation versatility.



C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-650 is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil's motion. Tinsel leads are carefully routed and attached to the spiders to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers.



Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. An in-line, outboard 2nd order high-pass filter, with Advanced Tweeter Protection Circuitry, is included to further enhance smoothness and improve power handling.



When it comes to value, C1 is the real deal!



Sold as a pair. Grilles not included.


General Specifications

Continuous Power Handling (RMS)


50 W


Peak Music Power


225 W


Recommended Amplifier Power (RMS)


10 - 75 W / Ch.


System Efficiency


91.0 dB @ 1 W / 1 m


System Nominal Impedance


4 Ω


System Frequency Response


59 Hz - 22 KHz ± 3 dB


Woofer Physical Specifications



Frame Outer Diameter* (A)


6.5 in / 165 mm


Grille Tray Outer Diameter (B)


6.84 in / 174 mm


Motor Outer Diameter (C)


3.15 in / 80 mm


Frontal Coaxial Tweeter Protrusion (D)


N/A


Frontal Grille Protrusion** (E)


0.85 in / 22 mm


Mounting Hole Diameter (F)


5.56 in / 141 mm


Mounting Depth (G)


2.44 in / 62 mm


*Does not take into account mounting tabs

**Frontal grille protrusion measured from mounting surface




Tweeter Physical Specifications



Flush Mount Fixture Diameter (A1)


1.87 in / 48 mm


Surface Mount Fixture Diameter (A2)


1.69 in / 43 mm


Flush Mount Mounting Hole Diameter (B)


1.625 in / 41 mm


Flush Mount Mounting Depth (C)


0.76 in / 19 mm


Flush Mount Tweeter Frontal Protrusion (D1)


0.29 in / 7 mm


Surface Mount Tweeter Frontal Protrusion (D2)


0.92 in / 23 mm


Crossover Physical Specifications



Width (W)


1.96 in / 50 mm


Height (H)


0.90 in / 23 mm


Depth (D)


1.34 in / 34 mm

Написать отзыв

Примечание: HTML разметка не поддерживается! Используйте обычный текст.
    Плохо           Хорошо